+
  • 水基涂料.jpg

Product Description

Water-Based Coatings for Sand Casting   Sand casting with water-based coatings

Performance Features :

This series of coatings exhibits excellent suspension stability, remaining free of caking during long-term storage and over-the-road transportation, with no settled sediment. They also demonstrate superior thixotropy, high solids content, uniform brush application, outstanding resistance to sand sticking, easy coating removal, and effective prevention of surface defects in castings. Application is possible by brushing, flow coating, or spraying.

How to Use :

This product series is supplied in slurry or paste form. Before use, add an appropriate amount of water and stir to dilute the material to the desired Baumé degree, then introduce it into the coating bath for dip coating. Detailed application instructions are available for each specific model. It is recommended to use a dedicated dilution and mixing machine to dilute the coating and adjust its Baumé degree, ensuring that it is brought to the specified value before proceeding with the dip-coating operation.

  1. Stir the paint in the container thoroughly using a dedicated mixer or a hand mixer.
  2. Pour the thoroughly mixed coating into the dip-coating tank, start the tank’s agitator, and add an appropriate amount of water for stirring. 10-15 Wait for a few minutes, then stop stirring: allow the paint to settle. 3-5 After a few minutes, measure the Baumé degree of the coating; repeat the above procedure until the required Baumé degree is achieved.
  3. Once the coating in the dip tank meets the specified requirements, stop stirring and begin the dip-coating process.
  4. After the sand core has been fully dipped, lift it out of the dipping tank and gently tilt and shake it to allow excess coating to drain off, ensuring that the coating spreads evenly and forms a smooth, uniform film.
  5. Place the dip-coated sand molds on the drying line for drying, ensuring that the coated surface is not touched.
  6. Dip coating 1–1.5 After one hour, start the mixer to stir the coating. 3 After stirring the coating in the dip tank uniformly for a few minutes, stop stirring and re-measure the coating’s Baumé degree. Once it meets the specified requirements, begin the dip-coating process.
  7. If the paint’s Baumé degree exceeds the specified limit, add water or additional paint, start the mixer, and stir while adding the appropriate amount of water or paint. 10-15 minutes, measure the Baumé degree of the coating until it meets the specified requirement.
  8. Stop dip coating 8 For more than one hour, stir the coating before starting dip coating. 10-15 minutes.
  9. In principle, stirring of the coating should be halted during dip coating to allow the coating to be applied under static conditions.
  10. Each dip-coating 4 Clean impurities from the dip-coating bath using a screen or similar tool once per hour, and remove settled coating from the bath once per day.
  11. Drain the coating from the dip tank and clean the dip tank once a week.
  12. Water-based coatings are prone to degradation during the summer. When production is suspended for an extended period, the coating should be returned to the paint tank or paint bucket; if necessary, an appropriate amount of preservative may be added, followed by thorough mixing before returning it to the paint bucket.

 

Sand Mold Coating (Water-Based) Model

Main Aggregate

Scope of Application

Application Method

Sand Mold Series 101

Zirconium powder composite

Steel castings

Dip Coating/Flow Coating/Brush Coating

Sand Mold Series 102

Mullite composite

Cast iron parts

Dip Coating/Flow Coating

Sand Mold Series 107

Pyrophyllite powder

Cast aluminum parts

Dip Coating/Flow Coating

Storage and Transportation

·Shelf life: 3 months

· Keep away from sources of ignition during storage, transportation, and use.

Packaging

· 40 kg per drum 、 Bagged, 25 kg per bag

Keywords:

Water-Based Coatings for Sand Mold Casting

Previous:

Next:

Application Cases

铁路件.png
铁路件.png

Dip-coating performance of the Sand Mold Water-Based 101 Series Coatings on Railway Components (Buffers)

涂料脱壳效果.png
涂料脱壳效果.png

Coating peeling performance

水基102系列涂料浸涂效果3.png
水基102系列涂料浸涂效果1.png
水基102系列涂料浸涂效果2.png
水基102系列涂料浸涂效果.png
水基102系列涂料浸涂效果3.png
水基102系列涂料浸涂效果1.png
水基102系列涂料浸涂效果2.png
水基102系列涂料浸涂效果.png

Dip-Coating Performance of Water-Based 102 Series Coatings

水基102在汽车配件上的使用效果.png
水基102在汽车配件上的使用效果.png

Performance of Water-Based 102 in Automotive Parts

铸件效果1.png
铸件效果2.png
铸件效果1.png
铸件效果2.png

Casting effect

Online Inquiry

If you have any suggestions, please leave us a message or send an email, and we will respond to you within one business day of receiving your email.

Submit